Видео

I tell my customers these won’t pass our calibration standards don’t test something you don’t want to know the answers too

The Dewalt dcd800 is the exact same size as the dcd794 so definitely worth it.

The ryobis, there were 3 at the store I went to. 1800 1900 and 2000 with same flow 1.2 But they are all rated for the same current draw. Something not right there. I bought the 2000 and now I think maybe should have got the 1800. I suspect they all have the same pump and motor.

I have a performance tool and I’m not sure if it’s just because the state in is a rust belt so the Zirk fittings are not always the original size or what but I have not had a great experience with it probably less than good experience. Constantly having to fight to get the thing to lock it leaks, but like I said, I don’t know if that’s the Zirk fitting or the adapter.

Can you do this again with the rigid compressor?

I recently bought the Duralast ($70 via ebay lol) and frankly amazed by it. Yeah it's a bit annoying to change torque settings & you need to watch the dial OR move slower to avoid going over, but it's still worth it. I've used the Snappy techwrench and it's nice, but not worth it outside of daily shop use.

Just got that Pittsburgh wrench for free with a $50 purchase….was concerned it was junk until I saw this video….unless you got a Unicorn Pittsburgh??

Royobi is the same as Milwaukee actually

I have the wheeler and it stiffened up recently. I think it may be because I might not have reduced the torque to store it.

U Gonna Try the Hilti Nuron gun ??😳

Hey could you do an updated torque wrench test as. New torque wrenches have been released from gear wrench on their 120xp line. I want to know their accuracy after 1000 cycles

Interesting. Most other reviews of the Ryobi 1800 rate it 1050 PSI and 1.4 GPM using a 2.5 orifice.

Great diagnostics & repair dude! I can't believe the engineers at Honda couldn't grace us with a fuel pump access panel. That's such a massive F-up! Honda & Toyota are usually really good about not doing S like that. My F-150 truck is the same way though, no access panel! I'm gonna have to cut a hole in my bed to get to it! Unreal! So dumb! And so is dropping the tank to "do the job correctly." No way, it's so much extra work for no reason.

I recently bought the Milwaukee inflator in this comparison in kit form with two M18 6.0 batteries, dual fast charger, and free tool (I chose the Hackzall) for $280.

I was surprised the mention of the "province of china" part and glad a few folks have addressed it in the comments. Im surprised there are people who still font know rhat taiwan is its own country especially an american

I have a brushless ozito hammer drill with 60Nm it cost me a $129 with a handle and no batteries but with batteries and charger $140

thank you brother for the video, I picked the Lexivon for my valve cover gasket, yellow on black is very easy to read.

I buy this like a fein because I’m a sucker for the blow molded case

Do you find issues when using an adapter? I do a lot of gunsmithing that requires a 1/2" drive torque wrench. But a lot of the 1/2" wrenches on the market have a minimum value that's too high. A 3/8" wrench has a more appropriate torque range but I would have to use a 1/2" adapter.

Purchased the Macnaught initially it disappointed me - I also had difficulty in locking it on and removing it - but persisted and soon learnt that once you mastered how to use the lock knob (that black bit) it is very easy and positive to lock on and also release - think outside of the box - now I use it on my excavator and loader pins rather than the Lock n Lube.

Excellent job! No BS with explanations of your ratings!

greetings to all the autistic torque wrench enthusiasts all over the world

Hello tools tested. Can you make a video about? What is the difference between the Elm327 mini and Elm327?

From your graphs, it looks like the 'scam' battery is the better deal. 10% less for 1/3 the price is not a bad deal.

Gonna get my a tool daily 🤟thank you for the vid. Guys dont forget to use his referral links for his efforts.

What I don’t like about the reversible harbor freight and snap on sets is that you have to use both hands to use them for external rings by separating the handles. It’s better to use one hand to use the tool and the other hand to cover the snap ring so it doesn’t go flying off and get lost.

There is some alternative with similar specs to M12 FPDX always with percussion function?

Thank you for this. Helped inform my purchase. I found that Tool Daily also carries an upgraded version of the base model you reviewed, fittings seem to be the all-brass of the base model, but bottle is plastic on plastic fitting with a wide mouth and wider base, still comes with extra nozzles, and what looks like the plastic adjustment shielding from the 1.5 liter model.

I'd use one of those to do the head bolts on my junk sub 100 hp econo shitbox.

Definitely would be interested in seeing some midrange priced electric pressure washers to see if there's any actual performance difference or are all 115v pressure washer roughly same due to amperage limitations. Maybe the more expensive just have better quality components and longevity?

You just saved me a lot of time and money watching your video. Thank you. I just purchased the number one pick AstroAI along with a set of 1.1 orifices.

Good video BTW. Hope it makes the Tool Show again, because this video has a broader potential audience than some of your others that have been referenced. To boost up Subscribers

I'm curious about the higher end models that claim PSIs that seem impossible from 120V (e.g. 3000 PSI) -from otherwise reputable brands (Greenworks, Dewalt, to a lesser extent Westinghouse), not just no-name stuff online who routinely lie. I am curious about that theoretical ceiling of pressure/flow from a 120V 15A source.

Project Farm showed Makita the far the best and I trust Project Farm.

I have the Ryobi brushless. Buddy of mine gave it to me since he doesn't have a need for it and it came with his kit. I've been happy with it in my limited use and, of course, the price 😊

I bought the Westinghouse to replace a Greenworks electric power washer. So far it's been great and I love the form factor. Power washer attachment in the front and hose attachment in the back with wheels so you can drag it around. Pretty happy with the wand but I'll likely upgrade the hose to a flexzilla at some point. Put a quick connects on every point. Works well with my chemical guys foam cannon. Nothing wrong with the Green Works. Just like the form factor on this a little better.

A little unclear in which options are the best, would love to see a ranking top to bottom from best to worst and why pick X over Y

What adapter do I need to connect a uberflex hose to the powryte?

What do you think about the blackline foam cannon?

I like the audio test portion... not all decibels are created equal. The higher pitch ones are very annoying. Additional tests could be items from Home Depot and Lowe's... which are the most common DIY store. Sun Joe comes to mind for budget home lawn and pressure washer equipment.

Doesn't bode well that 63% of its reviews on Amazon are 2 star and below!!!!!!!!!!!!!!!!! What does that mean for the 90 day warranty on Harbor Freight (mail the product back to China at victim's expense meaning disposable after the 30 day return period)?

Recently bought a Tekton 1/4" and finally cured an intermittent valve cover leak by carefully torqueing to 78in-lbs as the manual said. For years I'd been pussy-footing around and erring on the side of having them slightly under rather than risk them stripping.

Have the Ryobi (caught it on sale at the local home cheapo with a 10% off coupon for $90) coupled with an Essential Washer gun ($40) & Uberflex (blue) hose ($50) and the MJJC Pro 2 foam cannon ($80). The combo lays Adam's Mega Foam ($50/gal) like a champ--super thick.

This is really interesting. I say this because of the way you tested and what I had assumed. I had assumed that all these pressure washers that worked on a 15amp circuit would have similar performance, but watching testing done by Auto detailers of many of these pressure washers showed I was wrong. For example, I've seen the Active produce 2 GPM with a 4 orifice tip and produce 1100 psi, where the vast majority of others couldn't get close to that psi with the same tip. But your testing is different. It actually confirms my assumptions. Oh well.. I had to purchase the CAT 1800 because when I went to buy the Active VE52 on Amazon, they were sold out a week ago. I guess you got the one I was looking to buy.

Is the side of the garage you did this test on the same side you had to dig out and fix a couple years back?

Are you testing on 120 or 230v? It tends to make a huge difference on pressure washers. On 230v you can get over 3kw units while 120v tends to be limited to 1.8kw.

Top content! Thank you.

Milwaukee is actually assembled china not made in china.

Please put about 10 hrs on each one and run the psi and gpm test again . That will give you a better result on which one is better quality.

Nice! Could you do one for battery operated pressure washers?